Troubleshooting · Dryer repair
Dryer taking too long to dry? What to check, and when to call.
A dryer that heats but takes forever is almost always an airflow problem. Hot, damp air has to leave the house, and if it can’t, the clothes stay wet. Vents first, then the parts.
Before you start. Unplug the dryer before moving it or disconnecting the vent. On a gas dryer, be careful not to strain the gas line when you pull it out. Long drying times and a hot dryer cabinet are signs to clean the vent soon, not later.
Rather not do it yourself?
- One call, free to useTell us the make and what it’s doing.
- Matched on zip code and brandAn independent local technician who covers your area.
- Estimate before any workNothing gets opened up until you’ve agreed a price.
Likely causes
What usually causes it, most likely first.
- Clogged vent duct
Lint builds up along the duct and at the outside hood. Long runs, tight bends and old foil ducts clog fastest.
- Crushed or kinked duct
Pushing the dryer back against the wall can flatten a flexible duct.
- Lint filter or filter housing
A coated filter, or lint packed below the filter slot, cuts airflow.
- Washer not spinning fully
If clothes come out of the washer very wet, the dryer is being asked to do the washer’s job.
- Overloading
Packed loads don’t tumble, and the air can’t get through them.
- Moisture sensor or thermostat
On sensor-dry cycles, dirty sensor bars can end the cycle early. A failing cycling thermostat can keep the heat too low.
Checks you can do
Safe checks before you call anyone.
- Feel the airflow outside
With the dryer running, you should feel a strong, warm flow at the vent hood. Weak flow means a blockage.
- Clean the lint filter and its slot
Use a vacuum crevice tool in the slot where the filter sits.
- Check the duct behind the dryer
Pull it out a little and make sure the duct isn’t crushed. Rigid or semi-rigid metal duct holds its shape better than foil.
- Wipe the moisture sensor
Two metal strips inside the drum, usually near the filter. Clean them with a little rubbing alcohol.
- Check the washer’s spin
If clothes are dripping when they come out of the washer, look at the washer first.
When it’s a technician job
Call a technician if:
- Good airflow and it still takes too long
The heating side or a thermostat may be failing.
- The cabinet gets very hot
That is an overheating dryer. Stop using it until the vent and thermostats are checked.
- The vent runs through the roof or a long wall
Cleaning long or high runs needs the right equipment.
- Cycles end early with clothes still damp
The sensor or control may need testing.
What affects the cost
What moves the price.
We don’t quote prices here because they depend on the fault, the model and where you live. These are the things that make the difference. Ask for the estimate before any work starts.
- Vent length and route
A short run to an outside wall is quick. A long or roof vent takes more time.
- Parts
Thermostats and sensors are smaller jobs than heating elements or controls.
- Duct replacement
Replacing a crushed foil duct with metal is often part of the fix.
Straight answers
Common questions.
Why does my dryer take two cycles to dry?
In most cases the vent is restricted. The dryer heats the air, but the damp air can’t get out fast enough.
How often should a dryer vent be cleaned?
Clean the lint filter every load. The vent itself depends on how much you use the dryer and how long the run is. If drying times creep up, it’s time.
How much will the repair cost?
Nobody can give you an honest number without seeing the machine. The technician diagnoses it, tells you the price, and only starts once you have agreed to it. If you would rather replace the appliance, you can stop there.
Who actually comes out?
An independent local technician who covers your zip code. We are a free service that connects you with them; they are not our employees and we do not guarantee their work. Ask for their license (where your state requires one) and proof of insurance before they start.
Keep going
Dryer repair: more help.
Dryer repair by city
- San Diego, CA
- Chicago, IL
- Boston, MA
- San Antonio, TX
- Charlotte, NC
- Sacramento, CA
- San Francisco, CA
- New York, NY
- Los Angeles, CA
- Seattle, WA
- Dallas-Fort Worth, TX
- Houston, TX
- Washington, DC
- West Palm Beach, FL
- Austin, TX
- Phoenix, AZ
- Las Vegas, NV
- Denver, CO
- Atlanta, GA
- San Jose, CA
- Miami, FL
- Fort Myers, FL
- Portland, OR
- Philadelphia, PA
Still not working? One call.
A local technician, an arrival window and an estimate before any work starts.
(833) 586-3850